115/51 64M: Difference between revisions

Jump to navigation Jump to search
No edit summary
No edit summary
 
Line 111: Line 111:
* '''Penetration at 2 km''': 230 mm at 0°/130 mm at 60°
* '''Penetration at 2 km''': 230 mm at 0°/130 mm at 60°


Adopted in 1965 along with the TR-65, the MDS-115/1 Sahm Hamra (سهم حمرا, ''Red Arrow'') is the first APFSDS projectile developed in Riysa, the first armor-piercing projectile developed for the 64M gun, and the only steel monobloc penetrator fielded on a Riysian tank. It is made of 600 BHN tool steel with a soft steel armor-piercing cap, to prevent it from shattering due to spaced armor and ricocheting off of sloped armor arrays. The sabot is a simple ring-type made of steel, so the projectile uses six bore-riding fins for proper bore alignment, which are tipped with copper to reduce barrel wear.  
The MDS-115/1 Sahm Hamra (سهم حمرا, ''Red Arrow'') is the first APFSDS projectile developed in Riysa, the first armor-piercing projectile developed for the 64M gun, and the only steel monobloc penetrator fielded on a Riysian tank. It is made of 600 BHN tool steel with a soft steel armor-piercing cap, to prevent it from shattering due to spaced armor and ricocheting off of sloped armor arrays. The sabot is a simple ring-type made of steel, so the projectile uses six bore-riding fins for proper bore alignment, which are tipped with copper to reduce barrel wear.  


Thanks to its high muzzle velocity and L/D ratio of 13:1, it is superior to 105 mm APDS on both flat and angled armor, and has comparable performance to 120 mm APDS on sloped and spaced armor while being easier to aim, and all without using any valuable tungsten. Widely used during the Unification War despite the advent of the MDS-115/2, it could penetrate all tanks used by the Kingdom of Irbiya and the Mada'in Union at combat ranges, including the Royal Irbi Army's Chieftain Mk 2 and Mk 3. The introduction
Thanks to its high muzzle velocity and L/D ratio of 13:1, it is superior to 105 mm APDS on both flat and angled armor, and has comparable performance to 120 mm APDS on sloped and spaced armor while being easier to aim, and all without using any valuable tungsten. Widely used during the Unification War despite the advent of the MDS-115/2, it could penetrate all tanks used by the Kingdom of Irbiya and the Mada'in Union at combat ranges, including the Royal Irbi Army's Chieftain Mk 2 and Mk 3.


The Sahm Hamra was produced from 1964 until 1970, and then was produced again in 1972 to early 1973 due to tungsten shortages in the Unification War.
Adopted in 1965 along with the TR-65, the Sahm Hamra was produced from 1964 until 1970, and then was produced again in 1972 to early 1973 due to tungsten shortages in the Unification War.


====MDS-115/2====
====MDS-115/2====
==Combat Use==
==Combat Use==

Latest revision as of 21:47, 5 April 2020

115/51 64M
64M.jpg
A full 64M gun assembly.
TypeSmoothbore gun
Place of origin Riysa
Specifications
Weight2,425 kg (5,346 lb)
Length6300 mm
Barrel length5950 mm

Caliber115 mm
BreechHorizontal sliding wedge
RecoilHydropneumatic
Muzzle velocity1,680 m/s (5,500 ft/s) (APFSDS)
950 m/s (3,100 ft/s) (HEAT)
905 m/s (2,970 ft/s) (HE-Frag)

History

Design

Variants

Ammunition

APFSDS

MDS-115/1 Sahm Hamra

  • Total round mass: 22.0 kg
  • Projectile mass (with sabot): 3.196 kg (5.55 kg)
  • Penetrator length: 436 mm
  • Penetrator average diameter: 34 mm
  • Penetrator L/D ratio: ~13:1
  • Muzzle velocity: 1,686.5 m/s
  • Velocity loss per 1 km: 128.5 m/s
  • Penetration at 1 km: 270 mm at 0°/155 mm at 60°
  • Penetration at 2 km: 230 mm at 0°/130 mm at 60°

The MDS-115/1 Sahm Hamra (سهم حمرا, Red Arrow) is the first APFSDS projectile developed in Riysa, the first armor-piercing projectile developed for the 64M gun, and the only steel monobloc penetrator fielded on a Riysian tank. It is made of 600 BHN tool steel with a soft steel armor-piercing cap, to prevent it from shattering due to spaced armor and ricocheting off of sloped armor arrays. The sabot is a simple ring-type made of steel, so the projectile uses six bore-riding fins for proper bore alignment, which are tipped with copper to reduce barrel wear.

Thanks to its high muzzle velocity and L/D ratio of 13:1, it is superior to 105 mm APDS on both flat and angled armor, and has comparable performance to 120 mm APDS on sloped and spaced armor while being easier to aim, and all without using any valuable tungsten. Widely used during the Unification War despite the advent of the MDS-115/2, it could penetrate all tanks used by the Kingdom of Irbiya and the Mada'in Union at combat ranges, including the Royal Irbi Army's Chieftain Mk 2 and Mk 3.

Adopted in 1965 along with the TR-65, the Sahm Hamra was produced from 1964 until 1970, and then was produced again in 1972 to early 1973 due to tungsten shortages in the Unification War.

MDS-115/2

Combat Use